Loading…

Record Breaking Strongest Adhesive & Sealant

Adiseal adhesive & sealant destroyed the competition in an independent test. It was over 3 times stronger than the nearest competitor. Even the SCREWS STARTED RIPPING OUT in the test.

Cable Lubricant

(Last Updated On: 12 janvier 2022)

Cable pulling lubricant

Cable pulling lubricant is used to protect cable & wire from damage. This can happen when pulling cable or wire through a conduit or ducting. The lubricant for cable pulling works by reducing the friction of the cable. It also makes installation of the cable a lot easier. The wire pulling lubricant also speeds up the installation time, saving money on labour costs.


Lubricant for cable pulling

Cable is made up of several layers. Usually the conducting cores are near the middle. These conducting cores are usually covered by an electrical insulating material. On most cables, the conducting cores & it’s insulation is then protected further with an outer sheath. This outer sheath is usually made from flexible plastic material or sometimes rubber. On some cables there is added protection before the outer sheath. Steel wire armoured cable or SWA cable, has a steel wire covering before the outer sheath for extra protection. The diameter of SWA cable and it’s weight is a lot higher than other types of cable. This makes it harder to pull through conduit or ducting.

When pulling cable through conduit or ducting, the outer sheath can have high friction. This has the potential to damage the cable. If there is another cable already in the conduit or ducting, this increases the chances of damage. Lubricant for cable pulling will reduce this friction and reduce the chance of damage.


Types of cable pulling lubricant

We have 3 different types:

  • In a gel form called CabLube Gel
  • A liquid version called CabLube Liquid
  • An expanding foam version called CabLube Foam

CabLube Gel

cable pulling lubricant gel

This gel version of cable pulling lubricant clings onto to the cable providing the highest lubrication and protection when pulling cables & wires through conduit. It is available in 500ml bottles but can be made in larger sizes.

Suitable for different types of cable & wire including power, control, instrumentation & control. It’s compatible with most common types of cable jacket materials. The lubricant is easy to apply and provides easy cleanup. Low solid contents means less duct & conduit blocking.

  • Appearance: Gel
  • Odour: Slight characteristic
  • Colour: Azure
  • Viscosity: of about 26,000 cps
  • pH: 7 to 7.2
  • Operating temperature: -10°C to + 50°C
  • Solubility: Soluble in water


CabLube Liquid

cable puling lubricant liquid

This is a pourable & sprayable liquid lubricant designed to protect cable & wires from damage when being pulled through a conduit by reducing the friction. It is available in 500ml bottles but can be made in other sizes.

Suitable for different types of cable & wire including power, control, instrumentation & control. It’s compatible with most common types of cable jacket materials. The lubricant is easy to apply and provides easy cleanup. Low solid contents means less duct & conduit blocking.

  • Appearance: viscous liquid medium
  • Odor: Slight characteristic
  • Colour: White transparent
  • Viscosity: 52 sec. Ford Cup
  • pH: 7 to 7.2
  • Operating temperature: -5°C to + 50°C
  • Solubility: Soluble in water


CabLube Foam

cable pulling lubricant foam

CabLube Foam is a 100% evaporating cable pulling lubricant that expands into conduit. It makes cable installation easier by reducing the friction & reduces the chance of damaging the cable. As CabLube foam is 100% evaporating, it does not block up the conduit or ducting. This foam version of lubricant for pulling cables is available in 400ml aerosol cans.

Suitable for different types of cable & wire including power, control, instrumentation & control. It’s compatible with most common types of cable jacket materials. The lubricant is easy to apply and provides easy cleanup. Low solid contents means less duct & conduit blocking.

  • Physical state: liquid in spray. Aerosols, foam is Dispensed.
  • Colour: White
  • Odour: Slightly of soap.
  • Olfactory threshold. Not available.
  • Ph: 8
  • Melting point/freezing. 0°C.
  • Relative density. 1 kg/l.
  • Complete solubility in water.
  • Boiling point 100°C

For electrical insulation gels please see our IPGel products.


Cable pulling lubricant MSDS

To download the cable pulling lubricant MSDS, click on the links below for a PDF version.


Frequently Asked Questions About Cable Pulling Lubricant

Which cable pulling lubricant provides the most lubrication?

Adiseal CabLube Gel lubricant for pulling wire & cables provides the highest lubrication in our test.

What type of cables is the lubricant suitable for?

Our products are suitable for different types of cable and wire including power, control, instrumentation and control. It’s compatible with most common types of cable jacket materials.

Which lubricant for pulling wire & cables is the easiest to clean?

The Adiseal CabLube Foam provides 100% evaporation.

Where to buy wire pulling lubricant?

In the UK, our wire pulling lubricant can be purchased from local stockists. For other countries please visit www.guglue.com to buy cable pulling lubricant.

How to use wire pulling lubricant?

To use wire pulling lubricant, simply cover the cable before it is pulled through the conduit or ducting. Try to make sure the cable is thoroughly covered. On larger cables, a machine can be used to automate the the process of covering the cable in lubricant.